ASME B1.20.5-1991 GAGING FOR DRYSEAL PIPE THREADS(INCH)
|
ID： |
964DFBB90D2A403DBCB82CA458AADDCA |
|
文件大小(MB)： |
3.2 |
|
页数： |
66 |
|
文件格式： |
|
|
日期： |
2008-9-2 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
ADOPTION,I I,ADOpTIrn NcrrIcE 1,10 June 1992 for,ASME B1.20.5-1991,22 Janw 1991,ANSI B1 20.5-1978,31 October 1980,SUPERSEDING,ASME B1.2Q.5-1991 was adopted on 10 June 1992, and is approved for use by,the Federal agencies. The Amrican Society of Pkchanical Engineers,(ASME) prepared this ‘documnt which was approved by the American National,Standards Institute (ANSI) as an Amrican National Stxmdard. %th ASME,and ANSI have furnished clearances required.by existing regulations.,Copies of this documnt are stmked by the S-zation Documents,Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094t,for issvle to DoD activities only. All other requestors mst obtain,d o c a n t s from:,The kwrican Society of Mechanical Engineers,United Engineering Center,345 East 47th Street,New York, Ny 10017-2392,or,The flmerican National Standards Institute,11 Wst 42nd Street,New York, NY 10036-8002,Civil Caxdimtion ktivitiesr -m - Ac0,GsA-7FxE,NAsA-m,LN,Military Coordinating Activity:,DLA - IS,COPYRIGHT American Society of Mechanical Engineers,Licensed by Information Handling Services,COPYRIGHT American Society of Mechanical Engineers,Licensed by Information Handling Services,. AN AMERICAN NATIONAL STANDARD,GAGING FOR,DRYSEAL PIPE,THREADS,(INCH),ASME BI .20.5=1991,(REVISION OF ANSI B1.20.5-1978),The American Society of,Mechanical Engineers,~ ~~ ~~~,345 East 47th Street, New York, N.Y. 1001 7 -,COPYRIGHT American Society of Mechanical Engineers,Licensed by Information Handling Services,ASME BL.20.5 91 m 0759670 0082008 Y W,Date of Issuance: March 15, 1991,This Standardw ill be revised when the Societayp proves the issuance of a new,edition. There will be no addenda or written interpretations of the requirements,of this Standard issued to this edition.,ASME is the registered trademark of The American Society of Mechanical Engineers.,This code or standard was developed under procedures accredited as meeting the criteria for,American National Standards. The ConsensusC ommittee that approved the code or standardw as,balanced to assure that individuals from competent and concerned interests have had an opportunity,to participate. The proposed code or standard was made available for public review and,comment which provides an opportunity for additional public input from industry, academia, regulatory,agencies, and the public-at-large.,ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device,or activity.,ASME does not take any position with respect to the validity of any patent rights asserted in,connection with any items mentioned in this document, and does not undertake to insure anyone,utilizing a standard against liability for infringement of any applicable Letters Patent, nor assume,any such liability. Users of a code or standard are expressly advised that determination of the,validity of any such patent rights, and the risk of infringement of such rights, is entirely their own,responsibility.,Participation by federal agency representative(s) or person(s) affiliated with industry is not to,be interpreted as government or industry endorsement of this code or standard.,ASME accepts responsibility for only those interpretations issued in accordance with governing,ASME procedures and policies which preclude the issuance of interpretations by individual volunteers.,No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.,Copyright O 1991 by,THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,All Rights Reserved,Printed in U.S.A.,COPYRIGHT American Society of Mechanical Engineers,Licensed by Information Handling Services,FOREWORD,(This Foreword is not part of ASME BI .20.5-1991.),a In 1973, the American National Standards Committee B2, which had formerly been responsible,for pipe thread standards, was absorbed by ANSI Standards Committee B1 and,reorganized as subcommittee 20. A complete rewrite of the B2.2-1968 Standard on Dryseal,Pipe Threads was completed with the publication of ANSI B1.20.3-1976 for producth reads,and the ANSI B1.20.5-1978 Standarfdo r Gaging.,The product thread sfandard ANSI B1.20.3 establishes two classes of dryseal pipe threads:,Class 1 and Class 2. The classes differ only in inspection requirements. With Class 1 threads,inspecti.on of root and crest truncation is not specified. Class 2 threads are identical to,Class 1 threads except that inspection of root and crest truncation is required. This gaging,standard includes 6-step crest and root check gages, which, within theirli mitations, should be,helpful in establishing the degree of conformance ……
……